High quality amorphous transformer core factory: Nanocrystalline soft magnetic materials are a class of advanced materials that have garnered significant attention in recent years due to their unique properties and potential applications. These materials consist of nanoscale grains, typically ranging from a few to several tens of nanometers in size, which results in an ultrafine microstructure. This fine grain structure allows for improved magnetic properties such as high permeability, low coercivity, and low core losses compared to conventional soft magnetic materials. The enhanced performance of nanocrystalline soft magnetic materials makes them highly suitable for various technological applications, including power electronics, transformers, sensors, and electromagnetic shielding. Such as：Nanocrystalline Ribbons. Find even more info at nanocrystalline transformer core.
On the one hand, it can isolate eddy current, and the data is suitable for higher frequencies; On the other hand, due to the gap effect between particles, the data has low permeability and constant permeability; Because the particle size is small, there is basically no skin phenomenon, and the change of permeability with frequency is relatively stable; Moreover, the powder core can be prepared into special-shaped parts of various shapes for different fields; Finally, the damaged strip in industry can be crushed into magnetic powder, and then made into magnetic powder core, which can reduce the loss and improve the use value of data. The magnetoelectric properties of magnetic particle core mainly depend on the permeability of powder material, size and shape of powder, filling coefficient, content of insulating medium, forming pressure and heat treatment process.
Fe based amorphous alloys are competing with silicon steel in power frequency and medium frequency fields. Compared with silicon steel, iron-based amorphous alloy has the following advantages and disadvantages. The saturated magnetic flux density BS of iron-based amorphous alloy is lower than that of silicon steel. The filling coefficient of Fe based amorphous alloy core is 0.84 ~ 0.86. It shows that Fe based amorphous alloy has better resistance to power waveform distortion than silicon steel.
Amorphous Core is preferred choice for transformers required low losses at high frequency. We have amorphous c-cores,amorphous ribbon cores,amorphous cut cores,amorphous core transformers . Please find out more about crgo core material. There are 50% and 80% nickel iron materials available, in which we manufactures Mumetal Toroidal core and Mumetal C-core, for the applications in high quality Current Transformers and power supplies industries.
We know that the actual transformer always works in AC state, and the power loss is not only on the resistance of the coil, but also in the iron core magnetized by alternating current. Usually, the power loss in the iron core is called “iron loss”. The iron loss is caused by two reasons, one is “hysteresis loss” and the other is “eddy current loss”. Nanocrystalline magnetic core is a small part with magnetic conductivity. There are nanocrystalline particles with small particles in the center of nanocrystalline magnetic core. The working principle of nanocrystalline magnetic core is to absorb the common mode current in the cable through the principle of induction heating and convert it into heat to dissipate. rolled silicon steel sheet is selected. It is cut into long pieces according to the size of the required iron core, and then overlapped into “day” shape or “mouth” shape. In principle, in order to reduce eddy current, the thinner the silicon steel sheet, the narrower the spliced strip, and the better the effect. This not only reduces the eddy current loss and temperature rise, but also saves the material of silicon steel sheet. But in fact, when making silicon steel sheet iron core. Not only from the above favorable factors, because making the iron core in that way will greatly increase the working hours and reduce the effective section of the iron core. Therefore, when making transformer iron core with silicon steel sheet, we should start from the specific situation, weigh the advantages and disadvantages and choose the best size. Find more info on https://www.transmartcore.com/.
Commonly used transformer cores are generally made of silicon steel sheets. Silicon steel is a kind of steel with silicon (silicon is also called silicon), and its silicon content is 0.8 ~ 4.8%. The reason why silicon steel is used as the iron core of transformer is that silicon steel itself is a magnetic material with strong magnetic conductivity. In the energized coil, it can produce large magnetic induction intensity, which can reduce the volume of transformer.